Sunday, May 17, 2009

DIY Nikon SB-600 speedlight Flash Tube replacement

In a previous post I mentioned that one of my kids knocked over a light stand with an sb-600 attached. Well, I ordered the $8.52 USD flash tube from Nikon for the sb-600 speedlight, and did it myself last night. Works fine.


Things you need:
- 1 Nikon SB-600 Speedlight with a broken flash tube.
- Small philips screw driver (the small screwdriver set at the dollar store is fine).
- Soldering iron and solder (a solder sucker came in handy - borrowed it from a friend - thanks Matt).
- Replacement bulb (obviously): Part number: XE701 BTW (not required when phoning Nikon).

Optional:
- A way to drain the power from the capacitor/thingy that stores the energy to allow for a high powered flash.
- Small flat head screwdriver.

Prep: I didn't actively drain the power from the flash before I began working. After my flash broke, I could see that the tube was snapped in half. I removed the batteries. It sat without batteries for about three weeks. When I touched inside wires, I felt some power still in the flash, but never got zapped (though I have been zapped before while working on flashes).



Step 1. Place the flash bottom up and remove the two long screws at the end of the flash head.

Step 2. Pry off the rubber "Push" button on the hinge that allows for the head to be manipulated. There is also a spring underneath. I used a small flathead screw driver, but anything would have worked. It came off easily. Then unscrew the four screws underneath.

Step 3. Remove the cover on the opposite side of the hinge. Underneath the rubber cover is a very thin black adhesive film. Remove the film to expose the screws. Don't worry about tearing the film. Remove the four screws.

The bottom of the flash head should then easily be removed exposing the internal electronics. Notice the four small copper prongs that protrude from the bottom of the flash tube assembly. These prongs rub along the circuit board, and control the head's zoom. Try not to bend them, and definitely don't break them off. Make sure to check that they contact the board before reassembling.



Step 4. (optional). Drain the power so you won't get shocked. Here are some ways you may want to do it:
http://camerarepair.blogspot.com/2007/11/important-warning-camera-flash.html



Step 5. Four screws hold the zoom motor to the flash head. It is best to remove these screws to allow easier access to the solder points. However, eight screws are visible(ish), and only four need to be removed. Remove the two black ones on the far side opposite the pcb/circuit board. The other two screws to be removed run along the metal post on which the flash bulb assembly slides. The bulb assembly may actually obscure the one of the screws. The bulb assembly can gently be slid out of the way. The silver screws hold a pcb board to the flash head and don't need to be removed. The other row of screws (in between the two rows we are removing) can also stay in place.

Once the screws are removed, the only thing holding the bulb unit to the flash body are wires. Remove the wires from the clip to get more working distance between the board and the flash tube assembly.

Step 6. Remove the solder from the flash tube. The flash tube is solder at three points. One on each end, and a white wire that is also attached to the bulb. If you have a replacement bulb, it should be obvious the points that you need to desolder. Note: there is a second white wire that will also become desoldered; it joins the white wire from the bulb, at the same solder point.

Step 7. A transparent "rubber band" holds the bulb in the flash tube assembly and will need to be removed. I recommend removing the side with the white wire first, because on that side there is a slit in the rubber band to facilitate removal. Take note of which way the ends of the rubber band are facing in order to replace it the same way.


Step 8. Remove the tube. Kind of a pain, but it comes out.

Step 9. Slide the new bulb in and resolder. This is the simplest step, but this took me the longest. I preferred to solder the end without the white wire first. My rationale was that because there is a slit in the other side (the side with the white wire) of the rubber band, it will go on easier. Who knows? Also, my solder skills are lacking, so if I can do it, so can you.

Step 10. Put it back together.
A couple of things to remember: make sure that the copper prongs mentioned in step 3 are contacting the circuit board, you may want to check them out before replacing the screws that hold the flash tube assembly to the flash head. Also, make sure that the wires connecting the tube assembly to the flash are tucked way back. I put my flash back together, and it worked fine, accept for the 85mm zoom. The tube assembly was bumping the wires, and couldn't zoom all the way back. I had to reopen, and tuck the wires out of the way.

While I didn't try to break any components, I wasn't particularly gentile. The flash head seemed pretty durable, and moderately simple. If you can grow a third hand before beginning this project, it would be helpful.

Happy soldering!

Saturday, April 25, 2009

Thanks Matt for getting me out of the house to shoot some photos.



My friend Matt has been wanting to do a few night time HDR shots of certain building he and I saw a month or two ago. Here is my version of the building. It is near Deer Valley Airport in a business park just off of 19th Ave. Matt took some great shots. I took three photos, and this is the one I liked most. It is an HDR shot with exposures taken at 510 (8:30), 256 (4:16), 128 (2:08), 64, 30, 15, and 8 seconds. I am glad Matt got me out, and got me home when my voice started getting raspy.

On an unrelated note, I hope to soon a post on replacing the bulb in a Nikon SB-600 speedlight. I had the strobe on a light stand when my 1 year old knocked it over, and it landed bulb side down on the tile in the dining room. ARRGGHH. The zoom feature works, and I can easilty see the broken bulb through the clear plastic. Nikon's part dept. was closed 5 minutes before their scheduled closing time :p by the time I tried to order the part.

The bulb is on ebay for $29 + shipping but I hear that they are cheaper from Nikon. I have my soldering iron ready (three solder points), I just hope I can save it. It is on life support, and I hope it doesn't die on the operating table (my soldering is pretty bad).

Note: I am not a big fan of the "fakey/surreal" looking HDR photos, though they do have their place. If you look at this photo at full size. It looks more realistic.

Tuesday, April 21, 2009

Tiffany


Shot this photo of my sister-in-law in the garage. Two lights: an SB800 gelled blue shooting on a white background, and an Alienbees 800 with a large softbox camera right. I would have liked a little more distance between the subject and the background, but this was in my garage. Oh well. Then did about 3 minutes of post in Photoshop, just a quick high pass filter set to 75%ish opacity, vignetting, and desaturated just a tad.

Arnon, good luck on getting your black chair back. I love it.

Saturday, April 18, 2009

Black chair on the hill


Tessa always does a good job of helping me compose photos. Borrowed a black leather chair from the Livingstone house, and went up to a little hill not far from home. The chair turned out to be a lot heavier than it looked. Shooting through an umbrella, I think I would have preferred a softbox to control the light fall-off a little more. But I don't mind a little illumination on the immediate surroundings.

Thursday, April 16, 2009

dumped

My aunt was given the assignment of using strobes to take portraits. She decided to do a series of "dumped" photos. Here is one of the shots. We did it in my garage (I think it may have been a ploy to keep her own garage clean). Check them out here.




Three Alienbees total. Two on the sides and slightly above with 7inch reflectors (come standard with the strobes), and one alienbees shot into silver umbrella as the key light. We tried an sb-800 on the floor shooting at the background for a few shots. It was set to fire with the built in optical trigger. With the exception of two sb-600s, we used all my light.

We were able to shoot between 3.5 frames per second and 4.5 frames per second. The alienbees did a good job of keeping up, but a little power was lost. The first frame of each burst was noticeably lighter than the following.

Here are a couple of the setup shots. The shots are from our second sitting. As result, we managed to keep the mess somewhat under control. The chair front and left is where I stood to pour the food product on the poor recipient.

Before:

After:

Tuesday, March 31, 2009

Dance on white wall with butcher paper floor

I help out with the photography club at the high school. We started out with 30+ participants, and we are down to about 4-6 regulars. Which, to be honest, is on par with how most of the clubs at the school work. I dragged three Alienbees (800 x2 and 400) to school, and set them up in the teacher's work room. We laid some white butcher paper on the floor and went to town. 6.5 foot ceilings? Not recommended for shooting dance. Oh well, that is what we had, and it was a good learning experience for all involved. Thanks Sarah and Chris for being our guinea pigs.

Friday, March 20, 2009

Wednesday and Thursday Night HDR Photos







Thanks Ryan for taking us to Knight Transportation. I created a HDR gallery at my smugmug account here. The shots taken at Jesse's Auto Body Shop have been moved to smugmug gallery due to a google snafu with yesterday's post. I like last night's shots.

Thursday, March 19, 2009

My Childhood Memories


Here is my latest project: I am taking pictures of things associated with my childhood. Occasionally I am going to include some photos not taken by me, but taken when I was a kid. I am inviting my family members to come to the blog and comment on any memories that they may have of the photo, or the object in the photo.

Here is my teddy bear appropriately named "Teddy." He has been around a long time. I literally don't remember not having Teddy. He has one bad eye, and I don't remember very well where he came from.

Wednesday, March 18, 2009

Tuesday night's HDR





I am on spring break. As a result, I actually have stuff to post. After the last couple of nights I am getting the feeling that the better HDR photos have less lights, but more light. For example, all the above shots were made at the same location. However in the shot with the trucks I use the construction machinery to block the actual light bulbs. The light still enters the picture, but I don't get the nasty flaring. Maybe a star filter over the lens wouldn't eliminate the flare, but help control it?

Tuesday, March 17, 2009

I can't solder worth...

My aunt has a Canon Rebel XTi. In an effort to help eliminate camera shake, I decided to try to build her a remote for her camera. Fortunately, the XTi has a pretty simple remote control interface. It is basically a stereo 3/32 (smaller one) headphone jack connected to some buttons. To be honest I wish my Nikon D90's interface was as simple, but I digress.

I searched the web and I found very simple instructions here:
http://www.flickr.com/photos/s3is-rox/2236114921/

I bought a couple of push buttons at radio shack. I used a Goo Gone bottle as the housing. The wires were left over from other projects, I tried to use a jack from a cell phone headphone/microphone head piece. However the jack was designed to carry 4 signals instead of a regular stereo jack which carries three. As a result, the cell phone jack didn't line up in the body of the XTi as it should. I may have been able to get it to work with a little more effort, but it was more simple to just go find a stereo jack.

Here it is. It works, and isn't flashy but hey. I think it would look cool to put a bunch of L.E.D. lights in there, but...



As an aside: My soldering sucks. You would think that after all the "do it yourself" projects I have tried to do, I would start to get better. But no... I may be worse than when I started.